PCB-contaminated transformers can usually be distinguished by the nameplate on the transformer located on the outside casing. • Initiates, prepares and submits disposal requisitions for all PCB wastes. Transformer Disposal PCB and Non-PCB transformers and transformer oil disposal are services provided by ADCO Services which is a full-service transformer disposal company offering transformer disposal service to generators of transformer waste anywhere in The United States. Any Type Number beginning with “L” indicates that the transformer is PCB-contaminated. Capacitors are classified as large when they contain > 0.5 kg of PCBs. You must keep records to show that you disposed of the PCBsby one of these 2 methods. We also specialize in the identification of cost-effective approaches to manage PCB remediation waste. Transport of PCB wastes across or along public streets must have prior approval from the MOEE. Our instructions and procedures can easily be integrated into your quality management, environmental protection and occupational health and safety systems. Capacitors in electrical equipment vary in sizes from ice cubes to larger than refrigerators. PCB remediation waste is waste containing PCBs from a spill, release or other unauthorized disposal of PCBs, depending on the concentration of the source of PCBs, the date of release, the current PCB concentration in the materials, and whether the original source was authorized for use. Limitation of Assignment PCB Directive Council Directive 96/59/EC of 16 September 1996 on the disposal of … These procedures outline the requirements for the management of PCB-contaminated waste materials generated in laboratories, other academic areas and facilities and services operations. At the University over the years, these ballasts have been used from a wide variety of manufacturers. The handling of PCB wastes is subject to Ontario Regulation 362 – PCB Waste Management under the Environmental Protection Act of Ontario [RSO 1990]. Waste stream management to disposal, with preservation of the environment Experience in recycling PCB oil. Many provincial and federal environmental requirements apply. Almost every capacitor manufactured between 1930-1980 contains PCB dielectric liquids. In addition, Regulation (EC) No 850/2004 on persistent organic pollutants covers PCB. Capacitors may be found in a variety of locations within a building for example connected to A.C. motors > 30 hp wired to the electrical terminals. PCB-containing wastes that are municipal solid wastes may be placed with the regular garbage and accepted by your municipal waste landfill. PCB bulk product waste shall be disposed of in accordance with paragraph (a), (b), or (c) of this section. • Ensures disposal requisitions are submitted in a timely manner so PCB waste in accumulation areas does not exceed applicable quantity and time limits, with focus on the 30 day temporary storage time limit for most TSCA-regulated PCB … If the following brand names appears on the nameplate, the transformer contains PCBs: Table 1: Trade names of PCB-contaminated transformers. We are committed to creating a personalized program to meet our clients’ disposal and recycling needs. (a) PCB liquids. Our staff has the expertise to properly package, sample, analyze, characterize, profile and arrange for the disposal of any PCB Remediation waste generated. As North America’s leading industrial waste disposal company, Waste Management operates several Chemical Waste Management (CWM) sites across the United States that are specially permitted for the treatment and disposal of PCB-bearing materials. 40 CFR 761.62 - Disposal of PCB bulk product waste From the Cornell University Law School's Legal Information Institute. Manager, Environmental Protection The table below the map can be searched by key word or sorted by column heading. The exportation of PCB wastes outside of the country is prohibited. PCBs were sold in North America under the trade name AROCLOR. Fluorescent light ballasts also contain capacitors. Since the 1930’s, a generic fluid called “askarel” containing 40-70% PCBs were used in high voltage transformers. Clean Harbors handles liquid and … email: hazwaste.ehs@utoronto.ca. A PCB material is legally defined as any monochlorinated or polychlorinated biphenyl or any mixture that contains one or more of them. The identification of possible sources of PCB-contaminated materials, analysis and administrative requirements are outlined. Also Environment Canada has a publication on Identifying Lamp Ballast containing PCBs. Contact the Manager, Environmental Protection to arrange for disposal. Is PCB waste really a problem? Chemical Waste Management of the Northeast, Inc. Capacitors are hermetically sealed to reduce leakage. Contact Us to ask a question, provide feedback, or report a problem. Currently disposal of PCB wastes is limited in the number of facilities able to destroy these wastes. Light ballasts are discussed below. The Commission has carried out a study to facilitate the implementation of the waste related provisions of this Regulation. Contact the Office of Environmental Health and Safety to arrange for an analysis. PCB waste is generated in the form of production rejects as well as when properly dismantling old devices containing circuit boards and components. Special handling and storage requirements apply to any waste material with a concentration greater than 50 ppm of polychlorinated biphenyls [PCBs]. In order to remain compliant, all Emerald facilities must adhere to the specific conditions of a … United States Environmental Protection Agency, Chemical Waste Management Kettleman Hills Facility, National Rural Electric Cooperative Association (NRECA), Utility Solid Waste Activities Group (USWAG), National Fuel Gas Distribution Corporation (NFGDC), National Fuel Gas Supply Corporation (NFGSC), Radioactive/PCB waste treatment and landfill, Chemical Waste Management of the Northwest, Highway 17 North, Mile Marker 61, PO Box 55, 101 Parkway East Cogswell Industrial Park, PO Box 765, Pipeline & compressor systems decontamination, Catalytic hydrogenation (transformer oil), 3 miles east, 7 miles north of Knolls, Exit 41, Radioactive/PCB Waste Treatment mobile unit, Pipeline and compressor systems decontamination, New Castle Recycle Center, 3700 LaGrange Road, Energy Solutions/Duratek Services, Inc. Bear Creek Facility, Republic Waste Services - Itasca Landfill, 3 miles east, 7 miles north of Knolls, I-80, Exit 41. These facilities are approved by EPA to store or dispose of commercial PCB waste in accordance with the regulations outlined in Title 40 of the Code of Federal Regulations in part 761. Older equipment suspected of containing PCB materials, being removed from laboratories for scrap or decommissioning, must be carefully screened for PCBs. All disposal of PCB wastes is coordinated through the Office of Environmental Health and Safety. Clean Harbors is the only full-service polychlorinated biphenyl (PCB) disposal provider in the United States. There is no charge to departments for this test. Capacitors may vary in size from 5 KVAR to 200 KVAR range. An official website of the United States government. PCBs are regulated as hazardous substances under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980 . If PCB material is inadvertently brought into a metal recycling facility or hazardous waste facility, the owner of that facility may also be liable for clean-up, remediation, storage and disposal costs associated with PCB releases or contamination on the property. Industrial Disposal provides its customers with an efficient service for the safe removal and disposal of transformers, HV and LV switchgear and oils, as well as redundant electrical equipment contaminated with … A capacitor often can be recognized by the letters KVAR stamped on its nameplate. The Office of Environmental Health and Safety can be consulted regarding specific spill response procedures in individual areas. Fax: (416) 971-1361 ESG Edelmetall-Service GmbH & Co. KG has been recovering precious metals found in electronic waste for years. Summary of EU Waste Legislation on PCBs / PCTs. For example, an Aroclor containing 60% PCB would be designated Arocolor 1260. USEPA suggests incineration or disposal in a hazardous landfill for non-leaking PCB-containing ballasts. PCBs were used in a variety of applications including additives in lubricants, heat transfer dielectric fluids, adhesives etc. Warren County PCB Landfill was a PCB landfill located in Warren County, North Carolina, near the community of Afton south of Warrenton.The landfill was created in 1982 by the State of North Carolina as a place to dump contaminated soil as result of an illegal PCB dumping incident. For select approvals, you can access more information by clicking on the name of the facility in the table. Cost-effective and convenient solutions Historically, the major source of PCB waste at the University has been created when PCB-contaminated equipment has been removed from service or decommissioned. NR 157, Wis. Adm. Code. For assistance regarding PCB-contaminated materials, please contact: The Office of Environmental Health and Safety In the past, the University has produced these pumps that were contaminated with PCBs. see next slide for disposal of pcb materials containing equal to or greater than 50 ppm. A test will be performed to indicate the presence or absence of PCBs. These materials require special handling, storage and notification to the Ministry of Environment and Energy prior to being removed from a generating site for disposal. 40 CFR § 761.60 - Disposal requirements. Our PCB waste disposal professionals safely collect, transport, store, treat and destruct PCBs. Low-level wastes can be treated on the generator’s site using a chemical destruction process. Unless suspect equipment or laboratory sample has been verified as being PCB-free through an accredited laboratory, it is advisable that a sample be sent for analysis to determine the extent of PCB contamination or to verify the absence of PCBs. It is important for the University to recognize and identify possible sources of contaminated PCB wastes and implement appropriate handling requirements for such wastes. PCB Waste Holders: Report of Storage: The holders must annually report the storage and disposal of PCB waste to prefectural governors: Deadline for Disposal: PCB waste holders are to dispose or consign someone to dispose all PCB wastes by deadline set by the government. PCB Remediation Waste - New disposal options for PCB remediation wastes are implemented in 40 CFR 761.61. PCB wastes are subject to MOE as well as Environment Canada guidelines. The site, which is about 150 acres (0.61 km 2), was extremely controversial and led to years of lawsuits. Environment Canada developed polychlorinated biphenyl (PCB) regulations in 1977. 2-Chlorobiphenyl (2 chlorine atoms), 3-Chlorobiphenyl (3 chlorine atoms). Special attention should be paid to diffusion pumps and vacuum pumps. The small capacitors inside the ballasts are contaminated with high levels of PCB liquid if they were manufactured prior to 1980. These procedures should be made readily available in the area containing PCBs. The map shows the commercial storage and commercial disposal facilities in different layers. Small capacitors are generally associated with electronic or lighting equipment. Commercial Aroclors were blended with trichlorobenzene. We purchase scrap containing precious metals from across Europe. This includes all sources of wastes, from laboratories, building renovations and operations. Records should be maintained including the date of pick-up, the number of drums, names of transporters and destination of the PCB waste for disposal. Hazardous Waste > PCB Oil Disposal and Transformer Salvage & Disposal. Fluorescent lighting ballasts are easily identifiable containing PCBs or non PCB. The University, as required by the MOE, has decomissioned it’s registered PCB waste storage site located at the Insitute for Aerospace Studies in August of 2004 therefore NO PCB waste shall be stored longer than 90 days. PCBs have been used in many different products, including electrical equipment, surface coatings, inks, adhesives, flame-retardants, and paints. This includes all sources of wastes, from laboratories, building renovations and operations. EPA approval for <50 ppm PCB remediation waste disposal. About 10% of the PCBs produced since 1929 still remain in the environment today. how to dispose of pcb containing material: (pcbs less than 50 ppm) pcb materials containing less than 50 ppm are considered non-regulated. It is important to be able to identify the potential sources of these contaminated materials that may likely be encountered at the University. We take responsibility for managing your waste oil, including transport and treatment. All disposal of PCB wastes is coordinated through the Office of Environmental Health and Safety. That means you can either: 1. dispose of the PCBs or equipment in a way that destroys the PCBcontent 2. apply to permanently store the equipment underground if you cannot destroy the PCBcontent Email pcb-enquiries@environment-agency.gov.ukto discuss how to do this. The required environmental precautions vary due to the type of storage and type of PCB material being stored. PCB congeners differ (and are defined by) the number of chlorine atoms contained within the molecule, e.g. If any waste materials that are being disposed, the Manager, Environmental Protection should be notified. This section includes instructions for self-implementing cleanup and disposal of PCB remediation waste for a moderately sized site where there should be low residual environmental impact from remedial activities. A typical Askarel transformer may contain 30-40% PCBs and as high as 65%. Waste that is not immediately shipped for destruction must be stored on University property. Disposal and Storage of Polychlorinated Biphenyl (PCB) Waste Many PCB decontamination processes do not require approval from the EPA; however, some processes do require approval. Our PCB management facilities are permitted for the storage, consolidation and transfer of PCB waste and use EPA-approved alternative disposal methods. Exportation of PCB wastes outside the country is not allowed. Wastes that are contaminated with PCBs greater than 50 ppm require special destruction. Contaminated laboratory samples may also be produced from calibration samples. The following table and map show PCB commercial storage and disposal approvals issued by EPA. If you believe any of the information presented here is incorrect, please contact us at ORCRPCBs@epa.gov. dispose of pcb materials containing less than 50 ppm as c&d waste. Unless clearly indicated on the equipment, or the date of purchase can be confirmed to be after 1980, most capacitors in use must be assumed to be contaminated with PCBs unless tests have verified their absence. If a laboratory sample is labelled as PCB, Polychlorinated biphenyls, chlorinated biphenyl, Aroclor samples, the sample should be suspect as containing PCBs. If the PCB waste cannot be decontaminated, it must be stored in a registered PCB site on the generator’s property. Provinces then developed their own regulations to control the disposal of end of life equipment and materials containing PCBs. A transporter permitted to haul PCB waste should be contacted for disposal of drums filled with capacitors. We provide final disposal of PCB in specialized authorized plants, using the calorific content of the waste to produce heat or electricity through controlled incineration or co-incineration. All these uses were banned in Canada in 1977. Facilities for PCB Disposal and Incineration. E-Waste: The Seedy Underbelly of PCB Disposal March 03, 2020 by Lisa Boneta Over a decade past the first alarm bells of the effects of electronic and electrical waste, e-waste is still a major blight in the electronics industry. You must dispose of PCBs and materials that contain PCBsas a persistent organic pollutant and hazardous waste. This information is intended for consumers in need of PCB storage and disposal services and is not a definitive list of all approved PCB facilities. Any empty containers suspected of previously containing PCBs should be considered as PCB-contaminated waste material. If any waste materials that are being disposed, the Manager, Environmental Protection should be notified. Not only is PCB rubbish real, but the durability and toxicity of PCBs also make it a problem. Of the total PCBs used in the industrial/commercials sectors, Environment Canada has estimated that the educational sector accounts for 4% of the PCB inventory in all of Canada. Hydraulic equipment, oil-filled electromagnets, circuit breakers, voltage regulators, cables and vacuum pumps may contain PCB liquid. Our CWM facilities accept virtually all solid wastes containing PCBs including, but not limited to: The facility approvals to commercially store Polychlorinated Biphenyls (PCB) waste specifically reference and outline the parameters which are set forth in 40 CFR 761.65 - PCB Storage for Disposal. Disposal options for such wastes are limited and expensive. PCB waste subject to regulation under TSCA Nearly all (82%) of that waste ends up in landfills. Appropriate PCB disposal options depend on the type of PCB waste involved. The age of the equipment is a good indicator of potential PCB contamination. PCBs may be released into the environment, for instance when waste that contains PCBs is incinerated or stored in landfills. § 761.60 Disposal requirements. The handling of PCB-contaminated waste materials requires special consideration. Utility Solid Waste Activities Group member utilities, including We Energies, received approval from the Environmental Protection Agency in June 2014 to dispose of polychlorinated biphenyl (PCB) remediation waste generated at secure utility assets with as-found PCB concentrations less than 50 parts per million pursuant to 40 CFR 761.61(c). Any waste that is designated as a listed dangerous waste other than WPCB, or characteristic dangerous Environmental groups estimate that 25,000,000 tons of electronic waste (e-waste) is produced worldwide every year. This includes equipment, solids [including empty containers] and contaminated liquids. Askarel is the genetic term used to identify the combination of Aroclor and trichlorobenzene. Recycling of PCB waste. Decontamination procedures as they apply to emergencies are also addressed. Please remember that PCB waste must be transported by a licensed transporter and comply with ch. The Ontario Ministry of Environment [MOE] issues operating conditions for all PCB waste stored for more than 90 days. Our personnel are trained to evaluate each project and/or inventory to determine the most cost effective, turnkey environmentally correct option. Directive 96/59/EC on the disposal … The Office of Environmental Health and Safety maintains a list of models from various manufacturers that are PCB-contaminated. Our solutions for PCB waste disposal. Contaminated mineral oil usually contains < 1% PCBs. Should you suspect you have any PCB-contaminated equipment or material, please contact the Office of Environmental Health and Safety. PCB-containing wastes that are special or TSCA wastes must go to an appropriately permitted facility. Legislation. We offer the most comprehensive PCB destruction program that is in regulatory compliance with current government requirements: PCB hazardous waste audit, sampling, testing and weighing. The destruction of high-level wastes is limited to a single facility in Canada. Electrical engineers are used to seeing the early stages of a device's life. greater than 50 ppm PCB wastes, and within one year, are disposed of or incinerated at facilities permitted under federal standards to manage greater than 50 ppm PCB wastes. substances. Some Type Numbers are: LFAF, LFAN, LFWN, LNAF, LNP, LNS, LNW, and LNWN. Fluorescent light fixtures may contain several ballasts. (416) 978-7000 Equipment manufactured prior to 1980, is likely to have used PCB-contaminated fluids. E DISPOSAL Bangalore Dielectric Materials Division Central Power Research Institute 560080 GUIDELINES FOR PCBs, PCB-CONTAINING EQUIPMENT AND WASTE DISPOSAL ASTE IDENTIFICATION, TRACKING AND RECORD KEEPING 2014 In the event of a spill or fire involving PCBs, procedures have been developed to deal with spills and fires. Disposal Requirements. See Title 40 of the Code of Federal Regulations (CFR), part 761, subpart D to determine whether a disposal activity requires approval, and contact a local EPA Regional PCB Coordinator with any … Online Accident/Incident eForm for Employees, Online Accident/Incident eForm for Students, Contractors and Visitors, Training Matrix: Admin & Facilities Staff, Basic Health and Safety Awareness Training, Respiratory Protection Training and Fit-Testing, Environmental Health & Safety Program – Policies, Procedures and Guidelines, Laboratory Hazardous Waste Management and Disposal Manual, University of Toronto MOE Generator Information, 215 Huron Street - 7th Floor, Toronto, Ontario, Canada M5S 1A2. These facilities are approved by EPA to store or dispose of commercial PCB waste in … The limit of 50 ppm PCB contamination was established as a PCB waste. Click the arrows ">>" to see the legend and toggle the layers on/off. The Office of Environmental Health and Safety provides assistance in identifying, handling, storage and disposal options as well as all coordinating all regulatory requirements for PCB-contaminated materials. All wastes contaminated with > 50 ppm PCBs are classified as PCB waste and must be appropriately stored. To comply with environmental regulations, ALL PCB-contaminated materials must be disposed of through the Office of Environmental Health and Safety. For more information on our PCB Remediation Waste … They were defined by a 4 digit code of which the last 2 digits represent the % by weight of the chlorine content. The addition, the “Type Number” also indicates if the transformer contains PCBs.